Sale!

YZXStudio – ZYPDE

$6.50

***Default mode settings

Press and hold the key and then plug in the power. After the seven color lights flash red, green and blue, release the key to enter the default mode setting, and the color of the color lights

The corresponding functions are as follows:

Power on default Press the key briefly Press and hold the key

red  – 5V fixed voltage – Cycle from low to high Press the PPS gear length to enter step-by-step voltage regulation

yellow – 9V fixed voltage

green – 12V fixed voltage

Cyan- 15V fixed voltage

blue – 20V fixed voltage

purple – Pd2.0

white – 5V fixed voltage + millet Cycle from low to high Press the PPS gear length to enter step-by-step voltage regulation

Red flash – Low to high polling

Yellow flash – Low high low high polling

Green flash – From low to high, stop at high grade Cycle from low to high Press the PPS gear length to enter step-by-step voltage regulation

Cyan flash – A group of PPS drunk high voltage Change lift Press the PPS gear length to enter step-by-step voltage regulation

Blue flash – A group of PPS + millet after drunk Change lift Press the PPS gear length to enter step-by-step voltage regulation

Purple flash – Custom mystery function

White flash – Custom mysterious function + Xiaomi

After setting, long press the key to save, and the default light is off to exit. The next power on will run directly according to the default settings.

+Xiaomi represents a mobile phone disguised as Xiaomi, which is suitable for triggering Xiaomi PD adapter to output full load voltage and current. However, it may reduce the compatibility of other non millet adapters.

Warning: This product is only for professional users. After PD is triggered, it is strictly prohibited to access any equipment that cannot withstand high voltage, especially the version output by USB port. The store will not bear any loss if the equipment is burned out.

 

 

*The products on this page are shot and sent one by one. The two in the figure only show how to set up welding. Please know!

*This link module is one-way, and C port can only be input. Be careful not to buy it backwards.

*Part of the charging treasure will stop output when it is unloaded, saving power. After triggering, it should be loaded as soon as possible to maintain output.

*Only PD decoy trigger is supported, QC or other fast charging is not supported, and large USB port to C port cable is not supported. Be careful not to buy it wrong!

*If you don’t know what PD is, it’s not recommended to buy and waste money.

SKU: ZY12PDS Category: Tags: , ,

Usb-c pd2.0 3.0 to DC decoy fast charge trigger polling detector notebook power supply changed to type-C

ZY12PDS

 

***Zypde instructions:

This product can trigger any voltage within 3-21v, current within 6a and high power of 120W specified in pd3.0 and pd2.0.

After triggering, the user can supply the back-end load test or use through the USB motherboard or self welded cable.

PD trigger adopts hardware protocol IC, and its compatibility is not comparable to that of analog scheme.

The version with USB adopts high current pure copper base with small internal resistance.

TID certified high durability and high current C-Port, TVs anti short circuit and anti reverse connection, Japan Alps long-life light touch switch.

With USB welding position and 5.08 screw terminal welding position, it is convenient to make type-C to DC adapter.

Small volume 15mm wide * 28mm long. Once the DC line heat shrinkable tube is welded, you can charge your notebook with PD mobile power supply.

The ultra-low self power consumption is 1-2ma, which is 4 times smaller than the previous generation zy12pdn-8ma.

Good safety and stability, C port with reverse connection protection, CC short-circuit resistance to VBUS.

 

***Instructions

In the manual mode, press the key to switch gears. The colorful lights are on. Red, yellow, green, blue, purple and white represent the application for the 1st-7th gear,

In the continuous adjustable mode of PPS, press and hold for a long time to increase or decrease the voltage, and automatically trigger the corresponding gear in the automatic mode.

If PD is not triggered or timeout is not responded, the cyan light will flash and an error will be reported. If there is no corresponding gear in automatic mode, 5V will be triggered by default,

To customize the mystery function, the charger needs to support at least 5-11 VPPS gear. If it does not support it, the red light will flash and an error will be reported.

Wholesale more than 100, can customize any trigger mode, contact the shopkeeper for details.

Press and hold the key and plug it in to enter the default function setting mode.

 

 

 

Weight 0.5 kg
Dimensions 21 × 17 × 6 cm

Reviews

There are no reviews yet.

Be the first to review “YZXStudio – ZYPDE”

Your email address will not be published. Required fields are marked *